Model	FS-N15CN
Type	1 output type
Output	NPN
Input/Output configuration	M8 connector *1
Main unit/Expansion unit	Main unit
Control output	1 output NPN open collector 24 V or less; maximum 100 mA or less, residual voltage 1 V or less
External input	1 input Input time 2 ms (ON)/20 ms (OFF) or more, when selecting External calibration 25 ms (ON/OFF) or more
Response time	50 µs (HIGH SPEED) /250 µs (FINE) /500 µs (TURBO) /1 ms (SUPER) /4 ms (ULTRA) /16 ms (MEGA)
Multiple connections to Expansion units	0 units (expansion not possible)
Output toggle	LIGHT-ON/DARK-ON (switch-selectable)
Light source	Red, 4-element LED (Wavelength: 630 nm)
Timer function	Timer OFF/OFF-delay timer/ON-delay timer/One-shot timer
Protection circuit	Reverse polarity protection, Over-current protection, Surge absorber
Number of interference prevention units	0 units (connection not possible)
Case dimensions	H30.3mmxW9.8mmxL71.8mm
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Current Consumption	Normal: 900 mW or less (36 mA max. at 24 V, 48 mA max. at 12 V) 2 Econ on (ALL): 800 mW or less (32 mA max. at 24 V, 39 mA max. at 12 V) 2 Eco full: 470 mW or less (19 mA max. at 24 V, 23 mA max. at 12 V)
Environmental resistance	Enclosure rating	IP6634
Ambient light	Incandescent lamp: 20,000 lux or less, Sunlight: 30,000 lux or less
Ambient temperature	-20 to +55 °C (No freezing)
Relative humidity	35 to 85 % RH (No condensation)
Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions
Shock resistance	500 m/s2, 3 times in each of the X, Y, and Z directions
Case material	Main unit: glass-reinforced PBT; Cover: Sulfonic resin
Material	Adapter	Glass-reinforced PBT
Weight	Approx. 30 g
1 Use a cable of 30 m or less. 2 When the Power Mode is set to HIGH SPEED, 100 mW (4.0 mA) will be added. 3 About the enclosure rating when a small-diameter fibre unit (the diameter of the cable is o1.3 or o1.0) is used. IP66/IP65 cannot be satisfied when the type whose diameter is o1.3 and terminal can be separated (FU-4F/ 66/91/93/43/63/63T etc.) is used. When any small-diameter fibre units except for the above are used, IP65 is applied. 4 In any of the following cases, the enclosure rating IP66/IP65 cannot be satisfied. When the Fibre Unit and KEYENCE’s M8 connector cable are not connected (Recommended conditions to tighten up the M8 connector: Tighten it by hand first.Then retighten it as much as 1/16-1/8 of a rotation with pliers.) When the Fibre Unit and KEYENCE’s M8 connector cable are not connected When the dust cover of the Sensor Amplifier is open When there is debris in the dust cover When the waterproof adapter A/B are not used at the time of installation of a small-diameter fibre unit.

Previous product

Датчик Keyence FU-10

Next product

Датчик Keyence FU-16

Датчик Keyence FS-N15CN

Fibre Amplifier, M8 Connector Type, NPN

Описание
Получить КП

Описание

Model	FS-N15CN
Type	1 output type
Output	NPN
Input/Output configuration	M8 connector *1
Main unit/Expansion unit	Main unit
Control output	1 output NPN open collector 24 V or less; maximum 100 mA or less, residual voltage 1 V or less
External input	1 input Input time 2 ms (ON)/20 ms (OFF) or more, when selecting External calibration 25 ms (ON/OFF) or more
Response time	50 µs (HIGH SPEED) /250 µs (FINE) /500 µs (TURBO) /1 ms (SUPER) /4 ms (ULTRA) /16 ms (MEGA)
Multiple connections to Expansion units	0 units (expansion not possible)
Output toggle	LIGHT-ON/DARK-ON (switch-selectable)
Light source	Red, 4-element LED (Wavelength: 630 nm)
Timer function	Timer OFF/OFF-delay timer/ON-delay timer/One-shot timer
Protection circuit	Reverse polarity protection, Over-current protection, Surge absorber
Number of interference prevention units	0 units (connection not possible)
Case dimensions	H30.3mmxW9.8mmxL71.8mm
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Current Consumption	Normal: 900 mW or less (36 mA max. at 24 V, 48 mA max. at 12 V) 2 Econ on (ALL): 800 mW or less (32 mA max. at 24 V, 39 mA max. at 12 V) 2 Eco full: 470 mW or less (19 mA max. at 24 V, 23 mA max. at 12 V)
Environmental resistance	Enclosure rating	IP6634
Ambient light	Incandescent lamp: 20,000 lux or less, Sunlight: 30,000 lux or less
Ambient temperature	-20 to +55 °C (No freezing)
Relative humidity	35 to 85 % RH (No condensation)
Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions
Shock resistance	500 m/s2, 3 times in each of the X, Y, and Z directions
Case material	Main unit: glass-reinforced PBT; Cover: Sulfonic resin
Material	Adapter	Glass-reinforced PBT
Weight	Approx. 30 g
1 Use a cable of 30 m or less. 2 When the Power Mode is set to HIGH SPEED, 100 mW (4.0 mA) will be added. 3 About the enclosure rating when a small-diameter fibre unit (the diameter of the cable is o1.3 or o1.0) is used. IP66/IP65 cannot be satisfied when the type whose diameter is o1.3 and terminal can be separated (FU-4F/ 66/91/93/43/63/63T etc.) is used. When any small-diameter fibre units except for the above are used, IP65 is applied. 4 In any of the following cases, the enclosure rating IP66/IP65 cannot be satisfied. When the Fibre Unit and KEYENCE’s M8 connector cable are not connected (Recommended conditions to tighten up the M8 connector: Tighten it by hand first.Then retighten it as much as 1/16-1/8 of a rotation with pliers.) When the Fibre Unit and KEYENCE’s M8 connector cable are not connected When the dust cover of the Sensor Amplifier is open When there is debris in the dust cover When the waterproof adapter A/B are not used at the time of installation of a small-diameter fibre unit.

Получить КП

Для получения коммерческого предложения, пожалуйста, вышлите ваш запрос на электронную почту info@keyence-datchiki.ru с указанием требуемых позиций и реквизитами компании.

Категория: Датчики